确定空气注射技术影响半径的现场试验——以北京某焦化厂为例

以北京某焦化厂地下水污染场地为例,设计和建立了一套由1口注射井、3口地下水监测井和5口土壤气监测井组成的现场试验系统,并进行了现场注气压力与流量测试,地下水压力响应测试,溶解氧测试,氦气示踪测试与土壤气测试,确定了试验区域的最佳注气压力与流量和影响半径.注气压力与流量测试确定了最佳注气压力与流量为0.03MPa, 23.2m3/h.在最佳注气条件下,地下水监测井G3、G5、G8中,水位分别在10,15,15min后上升到最大值0.36,0.11,0.04m,地下水溶解氧浓度分别在60,65,75min后增加到7.35、2.47、0.74mg/L,以上结果表明,G3和G5响应较明显,G8响应不明显.土壤气监测井S2、S4、S5中氦气浓度分别在10,7,6min后达到最大值83%、13%、41%,S6中氦气无检出;S2、S3、S4、S5、S6中O2浓度分别上升到19.9%、19.6%、19.2%、19.0%、16.6%,以上结果表明,S2~S5响应较明显,S6响应不明显.综合分析以上4种测试结果,确定试验区域的影响半径为5m.     

基于国内实测燃煤电厂烟气汞排放估算的不确定度

参照测量不确定度评定与表示的国家技术规范,基于近年来我国燃煤电厂常规污控设备协同脱汞的现场测试数据(文献报道和实测值)及各省原煤w(汞)的实测值,初步构建了国内燃煤电厂烟气汞排放不确定度的计算方法,并以2010年的燃煤量、污控方式布局为基础,计算了该年度汞排放的不确定度. 结果表明:2010年我国燃煤电厂烟气汞排放的总不确定度为48.8t,占平均排放总量的34.3%;其中60.2%源于污控设备脱汞效率的不确定度,39.8%源于原煤w(汞)的不确定度;采用ESP(静电除尘)、ESP+WFGD(静电除尘+湿法脱硫)、SCR+ESP+WFGD(选择性催化还原脱硝+静电除尘+湿法脱硫)和FF(袋式除尘)大气污控组合的机组各存在6.0、32.2、9.7和0.9t的烟气汞排放不确定度,分别占各对应机组烟气汞排放量的19.3%、32.8%、84.6%和53.6%,其中SCR+ESP+WFGD污控组合烟气汞排放的相对不确定度最大. 随着我国烟气脱硝工作全面推行,2015年以后,SCR+ESP+WFGD污控措施(组合)的机组所占比例将会提高到66%以上,如果仍以现有数据为基础,则来自SCR+ESP+WFGD污控措施(组合)机组的烟气汞排放不确定度将会大幅增加,因此急需增加对该类装置脱汞效率的实测样本数量.      

An assessment of the air pollution data from two monitoring stations in Kuwait

This article assesses the air pollution data from two monitoring stations in Kuwait. The measurements cover major pollutants, i.e., CO, CO₂, methanated and non-methanated hydrocarbons, NO _x , SO₂, O₃, and particulate matter (PM10). The data also includes meteorological parameters, i.e., solar intensity, temperature, wind speed, and wind direction, and has been collected over a period 4 years, from 2001 to 2004. Data analysis includes the assessment of annual hourly averages and 1-h maxima. Typical pollutant concentration trends, similar to those previously reported for Kuwait and for other locations around the world, are observed except for particulate matter measurements, which have higher values because of proximity to the desert. Emissions of nitrogen oxides show a consistent increase over the years. This is caused by the increase in the number of motor vehicles and the expansion in power generation and industrial activities. The data collected is a subset of the air quality criteria, as defined by the US EPA (United States Environmental Protection Agency).     

Toxic substances: Measures and measurements†

The formulation of a sound policy for environmental protection and toxic substances control requires knowledge of the presence and concentration of environmental contaminants. For this reason monitoring programs have been set up in the Netherlands for water, drinking water, and air pollution. The Netherlands system for air pollution, monitoring of the substances SO2, NOχ, CO, O₃ is now fully automated. Some examples will be given to show the acquisition and management and interpretation of air pollution measurements.

Various smaller projects, supported by the Department of Health and Environmental Protection include measurement of indoor air‐contaminants, contaminants in soil and hazardous waste sites, and contaminants in biotic samples such as for instance PCB's in eels and seals and mussels. Moreover a Coordinating Committee regularly collects measurements from various sources in the Netherlands regarding pesticide residues and contaminants in food.

For cost‐effective monitoring the accuracy of the measurements must be chosen with regard to the biological effect concentration of the pollutant. The necessity of proper control measurements to establish background levels and the necessity of ring‐tests to increase interlaboratory reproducibility is discussed. In cost‐effective monitoring the minimum number of measurements, which are necessary to check the effect of environmental protection measures, must be defined through proper sampling.     

磷石膏制硫酸钾中试研究

以湿法磷酸副产的磷石膏和工业品氯化钾为原料 ,采用两步法 ,常温常压下 ,在 5 0 0 0t a工业化装置中 ,生产符合国标ZBG2 10 0 6 89农用一级品硫酸钾。整个过程流程较简单 ,能耗低 ,投资省 ,基本无“三废”排放。钾的收率达70 %。工艺条件稳定 ,产品质量稳定。中试结果与小试有较好的重复性 ,放大效果好。     

“无废城市”建设推进政策及措施的国别比较研究

“无废城市”建设已经成为应对城市固体废物（以下简称“固废”）管理挑战的国际趋势，我国也启动了“无废城市”建设试点工作。本文介绍了国际“无废城市”实践的背景和发展趋势，对我国和其他高收入国家的“无废城市”相关政策和具体实施方案进行了对比分析。分析结果表明，“无废城市”的推进政策与实施措施存在国别差异，我国的“无废城市”采纳了“问题导向”的推进策略，而高收入国家则是“目标导向”。最后对进一步推进我国“无废城市”建设试点工作提出了四点建议。     

石油污染土壤生物修复的中试系统构建与运行效果

构建了石油污染土壤生物修复中试系统,考察了中试规模下石油烃生物降解效率、矿化过程在生物降解中的作用.揭示生物修复过程中的系统微生物特性及其降解活性的关系,为现场污染土层生物修复工程评价和关键技术参数选择提供技术依据.结果表明,经过93d的运行,石油烃去除率达25.8%,其中典型轻质组分烷烃生物降解率最高,可达43.12%.中试系统运行稳定后,与现场调研的土壤微生物相比,其数量提高了1个数量级,活性提高了1.5倍.     

中国碳排放权交易促进低碳技术创新机制的研究

碳排放权交易已成为我国实施以市场为基础的重要环境规制之一,但此交易市场建设能否诱发我国低碳技术创新的有关研究仍然不足。以我国七个碳排放权交易试点为研究对象,采用合成控制法进行准自然实验,选取2004—2016年全国282个城市的面板数据,评估碳排放权交易试点政策对低碳技术创新的诱发效果,并使用排列检验法进行有效性检验;进而,定量分析碳排放权交易试点正式运行后对低碳技术创新的影响因素,探索七个试点效果差异的成因。研究发现:①碳排放权交易试点政策整体上诱发了试点地区的低碳技术创新活动。②各试点的政策效果存在一定差异,除重庆外的六个试点对政策响应较为迅速,其中北京、上海的诱发效果最显著,天津、广东、深圳和湖北次之,而重庆试点未能对政策作出充分的响应。③碳排放权交易对低碳技术创新作用中的政策"信号-预期"机制在我国首次得到验证,该机制在除重庆外的试点地区都得到了较好的构建。④碳排放权交易市场建设与区域产业结构升级产生了良好的协同作用,促进低碳技术创新,但其未能与外商直接投资形成相同作用;除重庆外,碳排放权交易这一市场型环境规制与控制型环境规制也呈现出协同作用。据此,应积极推进全国性碳排放权交易市场建设,以发挥其对低碳技术创新的诱发作用;但在统一市场建设过程中应重视地区差异,分步骤稳步推进;还应注重加强政府政策信号管理,引导企业开展低碳技术创新活动。     

中国低碳试点城市的碳排放现状

本文以国家发展和改革委员会公布的两批低碳试点城市(共36个)为研究对象,基于其2005-2011年间的单位GDP的CO2排放和人均CO2排放数据总结其碳排放水平,从区域分布、经济水平和人口规模三个方面分析了全国范围内低碳试点城市的碳排放现状。通过"十一五"期间碳减排成效和"十二五"期间碳减排目标两个方面分析了低碳试点城市的碳排放现状,并推测了低碳试点城市2015年的碳排放水平。研究显示,"十一五"期间低碳试点城市单位GDP的CO2排放和人均CO2排放均高于全国平均水平。2011年低碳试点城市单位GDP的CO2排放和人均CO2排放均高于各城市所在省份的平均水平。低碳试点城市单位GDP的CO2排放平均水平从东部到西部逐渐升高。人均收入高于全国平均水平的低碳试点城市中92%的城市的人均CO2排放高于全国水平。而随着城市常住人口规模的扩大,试点城市单位GDP的CO2排放逐渐降低,人均CO2排放却随着城市常住人口规模的扩大呈U型分布,其中大型城市的人均CO2排放水平最低。同时通过与同类地区对比分析,研究表明试点城市的低碳工作成效和减碳目标普遍优于同类地区。除直辖市外,32个低碳试点城市中28个城市2010-2011年单位GDP的CO2排放下降幅度和2015年单位GDP的CO2排放节能目标高于所在省份。在城镇化速度继续增加和经济总量保持上升的趋势下,到2015年低碳试点城市单位GDP的CO2排放虽然下降,但人均CO2水平仍呈上升趋势。我国的低碳试点城市建设任重道远。     

Vertical distribution of aerosol optical properties based on aircraft measurements over the Loess Plateau in China

Vertical distributions of aerosol optical properties based on aircraft measurements over the Loess Plateau were measured for the first time during a summertime aircraft campaign, 2013 in Shanxi, China. Data from four flights were analyzed. The vertical distributions of aerosol optical properties including aerosol scattering coefficients (σ_sc), absorption coefficients (σ_ab), Angström exponent (α), single scattering albedo (ω), backscattering ratio (β_sc), aerosol mass scattering proficiency (Q_sc) and aerosol surface scattering proficiency (Q_sc^′) were obtained. The mean statistical values of σ_sc were 77.45 Mm^− 1 (at 450 nm), 50.72 Mm^− 1 (at 550 nm), and 32.02 Mm^− 1 (at 700 nm). The mean value of σ_ab was 7.62 Mm^− 1 (at 550 nm). The mean values of α, β_sc and ω were 1.93, 0.15, and 0.91, respectively. Aerosol concentration decreased with altitude. Most effective diameters (ED) of aerosols were less than 0.8 μm. The vertical profiles of σ_sc,, α, β_sc, Q_sc and Q_sc^′ showed that the aerosol scattering properties at lower levels contributed the most to the total aerosol radiative forcing. Both α and β_sc had relatively large values, suggesting that most aerosols in the observational region were small particles. The mean values of σ_sc, α, β_sc, Q_sc, Q_sc^′, σ_ab and ω at different height ranges showed that most of the parameters decreased with altitude. The forty-eight hour backward trajectories of air masses during the observation days indicated that the majority of aerosols in the lower level contributed the most to the total aerosol loading, and most of these particles originated from local or regional pollution emissions.